![]()
![]()
Aerial Lifts for Construction
Aerial lifts are frequently used to perform work in areas that cannot be accessed from the ground or from solid construction. Each year, workers die or are seriously injured when using aerial lifts. When working with an aerial lift, an awareness of hazards is a must. This course will introduce common hazards associated with aerial lifts and will discuss safe work practices that should always be followed.
Course Length: 34 Minutes
Learning Objectives:
Course Languages:
Basic Rigging for Construction
Rigging is the process of moving heavy loads with slings, chains, hoists, and other special tools. The equipment used for lifting and moving loads is also called rigging.
Course Length: 77 Minutes
Learning Objectives:
Course Languages:
Blasting Area Safety
Blasting Area Safety creates an awareness of the activities that occur in a blasting area and describes the procedures of a typical blast sequence. This course is not designed for blasters or their crew, but is aimed at the other personnel that might be near a blasting site. The hazards of the site are discussed with the emphasis placed on flyrock, which is any material that travels beyond the boundary of the established blast area. The balance of the course discusses precautions taken at the site by the blaster-in-charge and the blasting crew, as well as precautions that non-blasting personnel should take.
Course Length: 29 Minutes
Learning Objectives:
Course Languages:
Blocking and Cribbing for Heavy Equipment
Servicing heavy equipment can be challenging. Heavy equipment is often large, uniquely shaped and impractical to move from the field for service work. Much service work requires the use of lifting tools such as hydraulic jacks, cranes and truck hoists. Because these lifting tools are used so frequently and are usually reliable, you may be lulled into forgetting that any lifting tool can potentially fail. But if you happened to be under a load during such a failure, chances are you would be injured or killed. That’s why raised heavy equipment must be properly blocked or cribbed. This lesson is designed to teach general blocking and cribbing safety principles and demonstrate how those principles are applied in various common blocking and cribbing procedures.
Course Length: 49 Minutes
Learning Objectives:
Course Languages:
Combustible Dust
This course provides a general understanding of the hazards, precautions, and potential consequences associated with combustible dust in the workplace. It will help learners recognize combustible dust hazards at their location and provide good housekeeping practices that will help minimize the likelihood of an explosion in the workplace. This course does not provide technical information suitable to engineers who design, build, and maintain equipment and facilities.
Course Length: 35 Minutes
Learning Objectives:
Course Languages:
Concrete and Masonry
Every year in the construction industry, there are many accidents, injuries and even fatalities resulting from formwork collapse during concrete and masonry construction. Most of these incidents are preventable. This course will focus on how to remain safe during concrete and masonry construction.
Course Length: 33 Minutes
Learning Objectives:
Course Languages:
Confined Space Hazards for Construction
People are injured or killed every year as a result of improperly entering or working in a confined space. Potential hazards in every confined space include explosions, toxins, and oxygen-deficient atmospheres. The Bureau of Labor Statistics reports an average of 20 people a year die from confined space hazards. More than half of the fatality victims are would-be rescuers. You may encounter confined spaces in virtually any occupation; therefore, you need to be able to recognize confined spaces and understand their hazards. This training will provide that knowledge.
Course Length: 30 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Aerial Lifts
This concise mini-module addresses the core elements that workers need to understand to conduct their aerial lift operations in a safe manner. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Aerial Lifts training program.
Course Length: 15 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Basic Rigging
This concise mini-module addresses the core elements that workers need to understand to conduct their rigging operations in a safe manner. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Rigging training program.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Concrete Construction
This concise mini-module addresses the core elements that workers need to understand to conduct their concrete operations in a safe manner. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Concrete Safety training program.
Course Length: 14 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Confined Spaces
This concise mini-module addresses the core elements that workers need to understand to conduct their Confined Space operations in a safe manner. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Confined Spaces training program.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Crane Safety
This concise mini-module addresses the core elements that workers need to understand to conduct their crane operations in a safe manner. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Crane Safety training program.
Course Length: 15 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Fall Protection
This concise mini-module addresses the core elements that workers need to understand when working around fall hazards on a job site. Employers can use this course to ingrain fundamental terms and employee responsibilities. This course is an excellent tool for organizations who want to bolster or supplement their current Fall Protection training program.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
Construction Mini-Module - Stormwater and Erosion Control Best Management Practices
Runoff from rainstorms and snowmelt picks up pollutants like sediment, oil, grease and other chemicals. Contaminated runoff may flow into storm drains or it may flow directly into lakes, rivers and streams. Preventing stormwater contamination ensures clean water for swimming, fishing and drinking.
U.S. Federal law requires construction sites to obtain stormwater permits any time an acre or more of land will be disturbed. As part of the permitting process companies implement stormwater pollution prevention programs, or SWPPPs. This course covers Best Management Practices (BMPs) for stormwater and erosion control.
Course Length: 15 Minutes
Learning Objectives:
Course Languages:
Contractor Safety
OSHA requires that companies provide a safe workplace for all workers. In order to provide a safe work place, rules must be in place. Accidents occur as a result of an unsafe condition or an unsafe act, or both. Both are the result of the actions of people. All accidents and injuries are preventable. This orientation will explain the rules in place to prevent accidents and provide a safe work place.
Course Length: 42 Minutes
Learning Objectives:
Course Languages:
Crane Hand Signaling Part 1
Cranes can be very dangerous when used in an unsafe manner. The signal person provides vital instructions to the crane operator to ensure operations are conducted safely . Part 1 of this two-part course on crane hand signaling covers basic skills and knowledge needed to use hand or voice signals to direct the movements of mobile and tower cranes.
Course Length: 24 Minutes
Learning Objectives:
Course Languages:
Crane Hand Signaling Part 2
Cranes can be very dangerous when used in an unsafe manner. The signal person provides vital instructions to the crane operator to ensure operations are conducted safely. Part 2 of this two-part course on using hand signals to direct the movements of mobile and tower cranes demonstrates standard hand signals. In addition, guidelines for using voice signals are provided.
Course Length: 36 Minutes
Learning Objectives:
Course Languages:
Crane Operator Safety for Construction
About 250,000 people operate cranes daily and have to deal with the risks involved. Workers in construction may already be aware of the proper operating techniques associated with cranes, but may sometimes easy to forget to implement them in their daily routine. This course stresses crane operator safety in the construction environment.
Course Length: 31 Minutes
Learning Objectives:
Course Languages:
Electrical Safety and Lockout/Tagout for Construction
Working with electricity can be dangerous. Every year, between 300 and 500 people in the U.S. are killed by electrocutions at work. To handle electricity safely, you need to know how it acts, how it can be controlled, and its hazards. Workers performing service or maintenance on machinery and equipment may be injured by the unexpected startup of the machinery or equipment, or release of stored electrical energy in the equipment. In fact, failure to lock out machinery before working on it is a major cause of injury and death in the United States. These deaths and injuries can be prevented by establishing and following an effective lockout/tagout program. This training will tell you more about electrical hazards in construction work, safe practices when working with electricity, and the lockout tagout program and how it can save your life.
Course Length: 56 Minutes
Learning Objectives:
Course Languages:
Ergonomics for Heavy Equipment
Working with heavy equipment can be physically demanding, requiring lifting, pushing, pulling, and handling heavy loads. Some tasks may be repetitive and require extended standing or sitting. Each person has physical limits or a “comfort zone” of activities that he or she can tolerate without developing lingering symptoms. Preventing work-related musculoskeletal problems rests on an ergonomically sound work environment, good work practices, and employee awareness. This course will introduce common risk factors and methods to prevent musculoskeletal injury when working with heavy equipment.
Course Length: 40 Minutes
Learning Objectives:
Course Languages:
Excavation and Trenching Safety
Trenching and excavation work is performed thousands of times daily, throughout the United States in all types of conditions. Unfortunately, each year in this country there are about 70 fatalities, in addition to over 1,000 work-related injuries associated with trenching and excavation incidents. Cave-ins can occur suddenly, without warning, giving little time to react. But their signs are present when proper safety precautions are not taken. This program has been created to increase your awareness and provide you with a better understanding of the laws, regulations, and company safety policies and procedures associated with your work.
Course Length: 48 Minutes
Learning Objectives:
Course Languages:
Exposure Hazards for Heavy Equipment
What we don’t know about exposure hazards can hurt us! Thousands were exposed to lead and asbestos before we learned about the exposure hazards and proper precautions for handling these materials. This training will help employees recognize types of exposure hazards, harmful effects and methods to eliminate or reduce exposure hazards.
Course Length: 34 Minutes
Learning Objectives:
Course Languages:
Fabrication Safety for Heavy Equipment
Working in a fabrication area requires your attention to safety. This course provides an introduction to safety awareness in fabrication areas.
Course Length: 35 Minutes
Learning Objectives:
Course Languages:
Fall Protection for Construction
Each year in the construction industry an average of over 350 workers fall to their death on American jobsites and more than 50,000 sustain an injury that requires them to miss at least one day of work. Fall injuries often result in injuries that cause permanent disabilities such as back pain, paralysis and brain damage. For that reason, OSHA’s fall protection standard deals with both human and equipment related issues for protecting workers from fall hazards. This training will cover systems and procedures designed to prevent falls off, onto or through working levels and to protect workers from being struck by falling objects.
Course Length: 53 Minutes
Learning Objectives:
Course Languages:
Fall Protection for Mobile Equipment
Not everything we have to work on is within reach. There are times we need a little help. Sometimes ladders are chosen, other times fixed scaffolds, and still other times mobile equipment like scissor lifts and articulating boom/bucket lifts are chosen. Working safely with this last category will be the focus of this course.
Course Length: 43 Minutes
Learning Objectives:
Course Languages:
Field Service Hazards for Heavy Equipment
Say you’re on a service call and you realize you don’t have a tool you need. What do you do? All work has been halted until you can service the equipment, so do you…Take time to go back to the shop and hold up the project longer? Use whatever is available to get the job done while running the risk of injuring yourself or damaging the equipment? Or ask the site manager if they have the tool you need? The last option is probably your best, but you could avoid the entire situation with better planning before making the service call. In this training, we’re going to examine the steps you can take to perform your job efficiently and safely from beginning to end.
Course Length: 49 Minutes
Learning Objectives:
Course Languages:
Fire Extinguisher Safety for Construction
A fire is the most common type of emergency for which organizations in the construction industry must plan. Small fires can often be put out quickly by a well-trained employee with a portable fire extinguisher. However, to do this safely, those employees must understand the uses and limitations of a portable fire extinguisher and the hazards associated with fighting fires. This training will provide that knowledge.
Course Length: 36 Minutes
Learning Objectives:
Course Languages:
Fire Watch
Every year, many workplace fires occur as a result of hot work – cutting, welding and other work that generates heat and sparks – being done without an adequate fire watch in place. Most – if not all – hot work incidents are completely preventable. A fire watch, conducted properly, is one of the most important ways to keep workers safe during hot work and prevent damage and destruction to property. This course covers the role and responsibilities of the fire watcher.
Course Length: 34 Minutes
Learning Objectives:
Course Languages:
First Aid for Back Pain
About one-half of all working Americans admit to having back pain symptoms each year. Back pain is one of the most common reasons for missed work and it is the second most common reason for visits to the doctor’s office.
However, many symptoms of back pain can be treated by the individuals experiencing them. First Aid for Back Pain not only relieves pain, but also stops the problem from getting worse.
Course Length: 20 Minutes
Learning Objectives:
Course Languages:
Grounding
What makes a good line or cable worker? It’s not just their knowledge of electrical principles or their experience – a good line worker or cable worker is one that is committed to taking the time and the steps necessary to work safely. In this course we will cover the reasons for grounding, planning your approach, and discuss details around the grounding procedure.
Course Length: 31 Minutes
Learning Objectives:
Course Languages:
Guarding Floor and Wall Openings and Holes v2
This is a summary of the Guarding Floor and Wall Openings and Holes Standard 1910.23 of the Occupational Safety and Health Act. This module is not intended to be totally inclusive but rather to highlight the information and requirements in the complete OSHA standard.
Course Length: 41 Minutes
Learning Objectives:
Course Languages:
Hand and Power Tool Safety for Construction
This presentation focuses on the importance of hand and power tool safety and the precautions needed to work safely with these tools. Increasing your knowledge about these topics will help reduce the risk of injury when working with tools during construction work.
Course Length: 29 Minutes
Learning Objectives:
Course Languages:
Hand, Wrist and Finger Safety Around Heavy Equipment
Your hands and wrists help you do a remarkable variety of tasks. You use your hands all day, everyday, both at home and at work and this makes them highly prone to accidents and injuries. Throughout the day, our hands can encounter any number of hazards, especially in the manufacturing, construction, mining, energy and petrochemical industries. Hand and wrist injuries can be accompanied by initial pain, but also may require prolonged recovery, including long hours of physical rehabilitation. Fortunately, these injuries are preventable. This course will present potential hand, wrist and finger hazards, as well as the steps to take to avoid them.
Course Length: 33 Minutes
Learning Objectives:
Course Languages:
Hazard Awareness for EPG Technicians
Learn about safety measures EPG technicians can employ when preparing for and performing service work on electrical power generators as well as when returning from and closing out after a service call.
Course Length: 41 Minutes
Learning Objectives:
Course Languages:
Hazard Awareness for Field Service Crane Operators
Most likely, you have already received training on the OSHA 1926.550 and ANSI B30.5 crane operating standards, plus you probably have hands-on, practical experience operating a crane – so what’s the purpose of this course? Well, it serves as a refresher, to remind you of actions you can take – such as remaining alert to the work you’re performing as well as your surroundings – in order to reduce or eliminate potential hazards on the job. However, if this is your first training on crane safety, pay close attention, as there’s a lot of information covered in a relatively short amount of time. You should also follow up with your supervisor to identify what additional training is needed.
Course Length: 38 Minutes
Learning Objectives:
Course Languages:
Hazard Communication for Construction
More than 32 million workers work with and are potentially exposed to one or more chemical hazards in more than 3 million American workplaces. With over 650,000 existing chemical products, and new ones are being introduced every day, a serious problem is posed for exposed workers and their employers. Hazard Communication (Hazcom) training is designed to provide construction workers with the information they need to know in order to understand the hazards and identities of the chemicals they are exposed to when working.
Course Length: 44 Minutes
Learning Objectives:
Course Languages:
Health Hazards in Construction
Workers in the construction industry face a number of health and safety hazards in their work sites everyday, including exposure to materials that can cause serious illness and affect the worker's health in the long term. This course was designed to provide awareness of the potential dangers of some common materials to which construction workers may be exposed.
Course Length: 57 Minutes
Learning Objectives:
Course Languages:
Hot Work
The OSHA standards lay out precautions for hot work and reference the NFPA (National Fire Protection Association) 51B Standard for Fire Prevention During Welding, Cutting and Other Hot Work for more detail about these precautions. This course is based on the OSHA standards and NFPA code, but your institution may have its own rules, and because your insurance company and local Fire Marshal have something to say about fire prevention it’s quite likely that your company’s procedures will be more stringent than the minimum requirements of the standards we’ll discuss.
Course Length: 54 Minutes
Learning Objectives:
Course Languages:
Human Element
So, how do we make good decisions? Knowledge alone doesn’t guarantee good decisions. That driver may have run that red light knowing there was a chance someone would get hurt, but he did it anyway. Why might that have happened? What might have affected his decision?The answers to these questions are going to be explored as we try to gain an understanding of the human element in safety.
Course Length: 55 Minutes
Learning Objectives:
Course Languages:
Hydraulic Lock Valve Accident Prevention for Telehandlers
The pressure in a typical telehandler hydraulic system is at least 3,500 pounds per square inch. Therefore, you must protect yourself from the hazards associated with hydraulic lock valves as you work with telehandlers. This course describes the special procedures for releasing pressure before working with those components.
Course Length: 83 Minutes
Learning Objectives:
Course Languages:
Introduction to OSHA for Construction
After the Occupational Safety & Health Act was passed in 1970, OSHA (Occupational Safety and Health Administration) was established to help make our workplaces safer. This course examines OSHA's role in promoting the health and safety of America's workers as well as the rights and responsibilities of the employer and the employee.
Course Length: 70 Minutes
Learning Objectives:
Course Languages:
Job Hazard Analysis
What if you could eliminate or minimize risks before an incident occurs? You can. In fact, a job hazard analysis provides a systematic way to identify potential hazards for a task so you can take measures to remove or control the risks. There are also additional benefits to conducting a job hazard analysis, which you’ll learn about in this course.
Course Length: 36 Minutes
Learning Objectives:
Course Languages:
Ladder Safety for Construction
Why do you need a course on Ladder Safety? All employees who use ladders need to know how to use them safely to prevent injury or death. This program covers the consequences of unsafe ladder use, the proper use of different types of ladders as well as ladder safety, inspection and storage.
Course Length: 35 Minutes
Learning Objectives:
Course Languages:
Load Securement for Heavy Equipment
The North American Cargo Standard forms the basis for the cargo securement and distribution regulations in the United States and Canada. The regulations are designed to ensure cargo stays in place, keeping drivers and other motorists safe. This training covers the regulations and best practices for loading, securing and unloading heavy equipment.
Course Length: 51 Minutes
Learning Objectives:
Course Languages:
Logging and Chainsaw Safety
Logging is one of the most hazardous industries in the U.S. Medical costs for chainsaw injuries amount to about $350 million per year in the U.S and every year, a number of loggers are fatally injured on the job. This course addresses the hazards of logging with chainsaws and safety precautions workers need to take to reduce their risk of injury on the job.
Course Length: 40 Minutes
Learning Objectives:
Course Languages:
Materials Handling for Construction
Your hands are your livelihood. So learn how to handle materials safely and keep your hands and yourself safe on the job.
Course Length: 37 Minutes
Learning Objectives:
Course Languages:
Materials Handling Safety Around Heavy Equipment
Material handling is a significant part of working with heavy equipment. Yet the ordinary nature of these activities can lull us into forgetting how important it is to take proper safety precautions when performing such activities. This course presents information on handling materials safely.
Course Length: 45 Minutes
Learning Objectives:
Course Languages:
OSHA Inspections for Construction and Multi-Employer Worksites
Very few people really look forward to OSHA inspections. All the same, an average of 1,000 employers per week receive a compliance inspection. Like it or not, inspections happen, so employers need to be prepared. This training provides an overview of the OSHA inspection process for construction and multi-employer worksites.
Course Length: 63 Minutes
Learning Objectives:
Course Languages:
Personal Protective Equipment (PPE) for Construction
Construction workers face a significant risk of death or injury from work-related hazards. The course presents an array of personal protective equipment (PPE) as well as the guidance on selecting, wearing and maintaining PPE.
Course Length: 62 Minutes
Learning Objectives:
Course Languages:
Personal Protective Equipment (PPE) Overview
Workplaces can be very dangerous and unpredictable places with loud noises, falling objects, flying sparks, toxic chemicals, whirling blades and belts, you name it. So what's one way to keep yourself safe? By wearing personal protective equipment, commonly known as PPE, you can protect yourselves against hazards and reduce your chances of getting hurt - or even killed.
Course Length: 34 Minutes
Learning Objectives:
Course Languages:
Powered Industrial Trucks: Operators Overview v2
Powered industrial trucks like forklifts, motorized pallet jacks, tuggers, tow motors and other powered equipment are used every day to lift and move equipment or materials… So what’s the big deal? Because of the high risk of injury and even death while operating a powered industrial truck, OSHA regulates their operation in 29 CFR 1910.178, and requires employers to provide training in their use. Specifically, powered industrial truck operators must receive comprehensive initial training, including facility specifics, a hands-on skill demonstration in the workplace and an evaluation. But the OSHA training requirements don’t stop there. Employers must also provide refresher training on Powered Industrial Trucks under certain circumstances.
Course Length: 54 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 1 - Overview
Think of the hazards you face at work, or even when doing home repairs or yard work. Do you wear personal protective equipment, or PPE? The Occupational Safety and Health Administration, more commonly known as OSHA, contributes the vast majority of injuries and fatalities to workers not wearing PPE, as well as not wearing the right kind of protection for the hazard.
Course Length: 14 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 2 - Head Protection
Hazards leading to head injuries are often difficult to anticipate and control. To protect yourself and even save your life, you should always:Assess your work environment or situation Anticipate potential hazards that could lead to a head injury. And, select the appropriate head protection for the hazard.
Course Length: 21 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 3 - Eye and Face Protection
Thousands of people each year suffer from work-related eye injuries that could have been prevented with the proper selection and use of eye and face protection. If you are exposed to any of these hazards, or any hazards that might damage your eyes or face, you must wear the right kind of protection.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 4 - Hand and Arm Protection
Selecting the best hand and arm protection can be a challenge. Gloves and sleeves offer varying degrees of protective qualities as well as limitations. So be sure to consult with your employer and the manufacturer’s recommendations when choosing the right hand and arm protection for the job.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 5 - Body Protection
Body protection helps keep contaminates off of your clothing and away from your body. And it helps safeguard you against chemical, electrical and physical hazards.
Course Length: 13 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 6 - Foot and Leg Protection
If you have ever stubbed your toe, you know that impact injuries can hurt. At work, heavy objects can fall on your feet. Typical foot injuries are caused by objects falling less than 4 feet and at an average weight of 65 pounds. If you work around sharp objects, you can step on something sharp and puncture your foot or brush up against sharp objects and cut your leg.
Course Length: 17 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 7 - Hearing Protection
In hazardous workplaces, we depend on our hearing to help alert us to dangers. Yet workplace hazards can include excessive noise levels that cause damage to our hearing or even hearing loss. By choosing the right hearing protection according to its Noise Reduction Rating (or NRR), we can bring excessive noise levels down to an acceptable level and still be able to hear those around us as well as any safety alerts or alarms.
Course Length: 18 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 8 - Respiratory Protection
Hazardous materials can enter your body by ingestion, absorption or inhalation. Proper respirator usage can protect you from inhalation hazards. Dusts, fumes, gases or vapors, and temperature extremes can penetrate and damage your respiratory system. Dust and fumes can irritate your nose and throat, and in some cases, your lungs. Gases and vapors can be absorbed from your lungs into your bloodstream, where they have the potential to damage your brain and internal organs.
Course Length: 15 Minutes
Learning Objectives:
Course Languages:
PPE for Heavy Equipment Part 9 - Electrical Protection
When potential electrical hazards exist in the workplace, it’s important to understand how to reduce or minimize your risk of electrical injury.Best practices recommend following proper safety precautions and only working on de-energized equipment and circuits that are equipped with lockout/tagout devices.
Course Length: 20 Minutes
Learning Objectives:
Course Languages:
Pre-Job Briefings for Electrical Work
Every day, all over the country, electrical work takes place. There are many risks associated with this type of work, and many different safety precautions are required depending on what is being done, as well as where and by whom it is carried out. Pre-job briefings make sure workers know about the current hazards and any changes that will affect how they work, as well as the safety precautions they need to take. This course covers how to conduct a pre-job briefing for electrical work.
Course Length: 16 Minutes
Learning Objectives:
Course Languages:
Pressure Vessel Safety
We use pressure vessels in a variety of residential and industrial applications. Yet we must respect the dangers associated with them. The release of stored or potential energy and hazardous materials can cause personal injury, loss of life and catastrophic property damage. In this course, you’ll explore how pressure vessels are categorized and regulated, what safety measures you can take to stay safe and prevent pressure vessel failures, and what to look for when visually inspecting pressure vessels.
Course Length: 30 Minutes
Learning Objectives:
Course Languages:
Preventing Strains and Back Injuries Around Heavy Equipment
Many pieces of equipment can be heavy and awkward to handle. Therefore, you run the risk of straining and injuring your back if you don't use proper lifting, handling and climbing techniques. This training is designed to help you minimize the risks of back strains and injuries when handling or lifting heavy parts and equipment.
Course Length: 37 Minutes
Learning Objectives:
Course Languages:
Scaffolding for Construction
An estimated 2.3 million construction workers, or 65% of the construction industry, work on scaffolds frequently. To reduce injuries and help prevent deaths, you should educate your employees on scaffold safety requirements. This course examines the common hazards associated with scaffolds and the basics to scaffold safety.
Course Length: 43 Minutes
Learning Objectives:
Course Languages:
Struck By, Caught Between
According to OSHA, the four most frequent types of construction incidents are falls from elevation, electrical shock and being either struck by or caught in/between materials and equipment. This course focuses on the steps workers can take to avoid being struck by or caught between hazards at work, including hazard awareness, prevention and control, with an emphasis on taking personal responsibility for safety.
Course Length: 33 Minutes
Learning Objectives:
Course Languages:
Tree Trimming Safety
Tree trimming operations require climbing, pruning, and felling trees. Hand and portable power tools such as loppers, trimmers, and chainsaws make the necessary cuts. Aerial lifts and chippers bring workers to the right height and clean up the worksite. All of these activities have the potential to be extremely hazardous. This course covers safety precautions for tree trimming.
Course Length: 42 Minutes
Learning Objectives:
Course Languages:
Trenching and Excavation Safety for Construction
Armed with the proper safety information you can take action and help prevent trenching and excavation injuries and fatalities. This course provides an overview of the hazards associated with this type of work and techniques to keep workers safe.
Course Length: 53 Minutes
Learning Objectives:
Course Languages:
Vehicle Inspection for Heavy Equipment
When driving to service calls or various work sites, you don’t have time to waste with a flat tire, overheated engine or some other maintenance problem that could possibly cause you to become involved in a motor vehicle incident. That’s why it’s essential to maintain your work vehicle and perform pre-trip inspections. Inspections help you identify and address problems before getting on the road. And ultimately, they help save you and your company time and money.
Course Length: 21 Minutes
Learning Objectives:
Course Languages:
Welding, Cutting, and Brazing for Construction
Construction workers must take steps to prevent injury and damage when welding, cutting and brazing. The risk from fatal injuries alone is more than four deaths per thousand workers over a working lifetime. Therefore, care must be taken to ensure that work is performed safely. This course introduces common hazards associated with welding, cutting, and brazing and ways to prevent injury and damage.
Course Length: 35 Minutes
Learning Objectives:
Course Languages:
West Nile Virus
West Nile Virus (WNV) is a potentially serious illness, most often spread by the bites of infected mosquitoes. This course covers the history of the virus and what individuals can do to minimize their risk of exposure to it.
Course Length: 32 Minutes
Learning Objectives:
Course Languages:
Work Zone Safety
The objective of this class is to help you understand the dangers associated with highway and road construction as well as how to protect yourself. With the number of traffic fatalities in highway work zones rising, it is imperative workers understand the unique problems associated with working with live traffic.
Course Length: 39 Minutes
Learning Objectives:
Course Languages:
Worker Orientation for Construction v2
We believe accidents and injuries are preventable and they occur as a result of unsafe conditions and an unsafe acts. This orientation course explains some basic safety rules to help prevent you from injuring yourself or someone else.
Course Length: 32 Minutes
Learning Objectives:
Course Languages:
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||




